Whirlpool provides a limited 1-year warranty that covers labor and some replacement parts. However, some appliance models have more coverage than others. Refer to your appliance manual to check your model’s coverage beyond the limited warranty.
Should You Repair or Replace Your Broken Whirlpool Washing Machine?
Whirlpool washing machines can cost anywhere from $700–$1750. The average repair cost is less than the minimum cost to buy a new machine.
If your washer isn’t over ten years old, we recommend repairing it — although some machines last longer than ten years. If you’re unsure about whether your washing machine is worth fixing or beyond repair, we recommend contacting your local appliance professional.
Common Whirlpool Washing Machine Problems
If your Whirlpool washer is experiencing issues, don’t panic just yet. Whether you’re in need of a repair or replacement part, we can fix most problems with Whirlpool washers. Check out some common problems below that others have experienced, along with some possible causes.
Whirlpool Washer Makes Strange Noises
Do you hear loud or unusual noises when your machine is spinning? There may be an issue with the drive belt or drive pulley. Both parts are responsible for turning your washer’s tub.
An appliance technician should replace a defective drive belt or pulley system. The tub bearing, which helps the tub spin freely, could also be worn and must be replaced.
Whirlpool Washer Won’t Start
First, ensure there are no power-related issues in your home (e.g., a tripped breaker, unplugged washer, etc.). If this isn’t the case, the lid may not be locking — even if it appears closed. On some models, an unlocked lid signals to the washer that it cannot start the cycle.
A defective part that needs replacing, such as the line fuse, display board, or timer, could also be the culprit for a washer that won’t start.
Whirlpool Washer Lid Doesn’t Stay Locked
Sometimes your washing machine won’t start because the lid is open. Other times, it starts but the lid still doesn’t stay locked. So, what do you do in this situation?
The door’s boot seal or hinge may be to blame on front-load models. Other possible causes include a faulty door lock or latch. After replacing the defective part, you should notice a drastic improvement in your washer’s closing functionality.
Whirlpool Washer Gives an LD Error Code
An LD error code for Whirlpool washing machines means your washing machines your washer needs to be draining more quickly. The drain hose may be either clogged or installed improperly. In either case, we recommend having an appliance technician examine your hose to ensure your washer operates safely and efficiently.
Whirlpool Washer Emits a Burning Smell
On laundry day, you should smell freshness. If you smell burning instead, it can be a definite cause for concern. It’s possible that your washer’s drum is stuck. If this happens while the rubber belt rotates, it can produce a burning smell.
If the belt itself is damaged in any way, it will need to be replaced to eliminate the cause of the smell.
Whirlpool Washer Accumulates Rust Spots on the Lid
When rust spots form on the lid of your washer, it’s easy to understand why you’d want to get rid of your machine altogether. After all, who wants a rust-coated load of laundry? Rest assured; this is a fixable problem.
Some DIY solutions propose cosmetic fixes for removing rust, but we don’t recommend this approach, as it’s temporary and ineffective. Your local Mr. Appliance technician can remove rust the correct way, making your washer appear like new.
Whirlpool Washer Water Doesn’t Cover Clothes
The water inlet valve delivers water to your washer. When this valve is clogged or defective, you may notice that your washer is not filling with enough water. Depending on the condition of the valve, it may need to be replaced. The water level pressure switch could also be at fault for not telling the water inlet valve to turn on.
One other simpler cause is a twisted water-fill hose that won’t allow enough water to penetrate. This requires only untwisting rather than a replacement.
Whirlpool Washer Stops in the Middle of a Washing Cycle
This malfunction likely points to a problem with the lid-closing mechanism, the water inlet valve, or the control board.
If the lid opens during one of your machine’s wash cycles, your washer can suddenly stop. This feature varies by model, so you’ll want to check to see if you have the type of washer that pauses between cycles when the lid has been opened.
A problem with your machine’s water inlet valve can cause your washer to stop at the rinse cycle. When water cannot properly flow through the valve, it limits the amount of water that’s emptied into the tub.
The control board helps power your washer’s electrical parts. If it’s damaged in any way, it can affect the way your washer runs.
Whirlpool Washer Stuck on Sensing
The sensing feature on your Whirlpool washer gives the machine information about the volume of your laundry load. It does this by slowly spinning and then filling the tub with the correct amount of water based on the load size.
If your machine is stuck on sensing mode, you could be dealing with a clogged water inlet valve, a damaged shift actuator, or a faulty drive motor.
When a water inlet valve is full of debris, water can’t get through. If water can’t get through, your appliance can’t transition to the wash cycle.
The shift actuator, which actually signals to your machine to shift through cycles, needs to function well in order for your washer to progress through cycles.
The drive motor generates power for your machine. When this gives out, your washer’s drum can’t spin or transition to the next cycle.
Whirlpool Washer Leaking Water
A leaking washer can be due to a number of factors. One tactic to pinpoint the cause of the leak is to locate where the leak is happening.
- A bottom leak could be caused by a damaged water pump, a loose drain pipe, or a defective washer tub seal.
- Droplets from the washing machine hose can likely be attributed to a loose or clogged component, such as the rubber washers or drain hose.
- Water dripping into the washer when your machine is off means that you must have your washer inlet valve checked.
- Leaking from your appliance’s door is usually due to a weak door seal or door latch. You may also be using excess detergent, creating a blockage in the overflow tube.
If you’re noticing puddles in or around your washing machine, it is always best to check with an appliance professional before applying any quick DIY fixes.
Types of Whirlpool Washing Machines We Can Fix
- Top load
- Front-load
- Stackable
Whirlpool Washer Series We Service
- Whirlpool Cabrio, including the Platinum series
- Whirlpool Duet
We Help you Find the Whirlpool Washing Machine Parts You Need
Whether you’re looking to complete a DIY repair project or receive service from one of our technicians, we have the Whirlpool washer repair parts needed to perform efficient repairs. We have the following parts on hand:
- Belts
- Timers
- Pumps
- Hoses
- Lid switches
- Lid plungers
- Pressure switches
- Agitator assemblies
- Drive spindles
- Wigwag plunger/lifters
- Transmission mode levers
- Transmissions
- Solenoids
- Damper/snubber pad
Still looking for a part that’s not listed? Contact your local Mr. Appliance team.
Find a Whirlpool Washing Machine Technician Near You
If your appliance isn’t working optimally, take advantage of our Whirlpool washing machine repair service. Call us or schedule an appointment online to speak to one of our appliance professionals.
Click to call
